From 0c9cec39f4611d86c7ca9730be9edf2a928b14e4 Mon Sep 17 00:00:00 2001
From: jbruce <jbruce12000@gmail.com>
Date: Wed, 21 Nov 2018 11:36:58 -0500
Subject: [PATCH] - adding my config.py

---
 config.py | 88 +++++++++++++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 88 insertions(+)
 create mode 100644 config.py

diff --git a/config.py b/config.py
new file mode 100644
index 0000000..355a98e
--- /dev/null
+++ b/config.py
@@ -0,0 +1,88 @@
+import logging
+
+########################################################################
+#
+#   General options
+
+### Logging
+log_level = logging.INFO
+log_format = '%(asctime)s %(levelname)s %(name)s: %(message)s'
+
+### Server
+listening_ip = "0.0.0.0"
+listening_port = 8081
+
+### Cost Estimate
+kwh_rate        = 0.18  # Rate in currency_type to calculate cost to run job
+currency_type   = "USA"   # Currency Symbol to show when calculating cost to run job
+
+########################################################################
+#
+#   GPIO Setup (BCM SoC Numbering Schema)
+#
+#   Check the RasPi docs to see where these GPIOs are
+#   connected on the P1 header for your board type/rev.
+#   These were tested on a Pi B Rev2 but of course you
+#   can use whichever GPIO you prefer/have available.
+
+### Outputs
+gpio_heat = 11  # Switches zero-cross solid-state-relay
+gpio_cool = 10  # Regulates PWM for 12V DC Blower
+gpio_air  = 9   # Switches 0-phase det. solid-state-relay
+
+heater_invert = 0 # switches the polarity of the heater control
+
+### Inputs
+gpio_door = 18
+
+### Thermocouple Adapter selection:
+#   max31855 - bitbang SPI interface
+#   max31855spi - kernel SPI interface
+#   max6675 - bitbang SPI interface
+max31855 = 1
+max6675 = 0
+max31855spi = 0 # if you use this one, you MUST reassign the default GPIO pins
+
+### Thermocouple Connection (using bitbang interfaces)
+gpio_sensor_cs = 27
+gpio_sensor_clock = 22
+gpio_sensor_data = 17
+
+### Thermocouple SPI Connection (using adafrut drivers + kernel SPI interface)
+spi_sensor_chip_id = 0
+
+### amount of time, in seconds, to wait between reads of the thermocouple
+sensor_time_wait = .5
+
+
+########################################################################
+#
+#   PID parameters
+
+pid_ki = 0.1  # Integration
+pid_kd = 0.4  # Derivative
+pid_kp = 0.5  # Proportional
+
+
+########################################################################
+#
+#   Simulation parameters
+
+sim_t_env      = 25.0   # deg C
+sim_c_heat     = 100.0  # J/K  heat capacity of heat element
+sim_c_oven     = 2000.0 # J/K  heat capacity of oven
+sim_p_heat     = 9450.0 # W    heating power of oven
+sim_R_o_nocool = 1.0    # K/W  thermal resistance oven -> environment
+sim_R_o_cool   = 0.05   # K/W  " with cooling
+sim_R_ho_noair = 0.1    # K/W  thermal resistance heat element -> oven
+sim_R_ho_air   = 0.05   # K/W  " with internal air circulation
+
+
+########################################################################
+#
+#   Time and Temperature parameters
+
+temp_scale          = "f" # c = Celsius | f = Fahrenheit - Unit to display 
+time_scale_slope    = "m" # s = Seconds | m = Minutes | h = Hours - Slope displayed in temp_scale per time_scale_slope
+time_scale_profile  = "m" # s = Seconds | m = Minutes | h = Hours - Enter and view target time in time_scale_profile
+