firmware-base/docs/omron/modbus.md

No registers found, Page Number 4-13

Variable Area (Setting Range) List (Page 5-2)

type	description	address in Hex	address in decimal	parameter name	settings / range	level	default
FC 03 / FC 16	Process Value (PV)	2000	8192	PV	Temperature/Analog specific range (See manual)	Operation
FC 03 / FC 16	Status	2001	8193	Status 12	Refer to 5-2 Status for details	Operation
FC 03 / FC 16	Internal Set Point	2002	8194	Internal Set Point *1	SP lower limit to SP upper limit	Operation
FC 03 / FC 16	Heater Current 1 Value Monitor	2003	8195	Heater Current 1 Value Monitor	0.0 to 55.0 (H'00000000 to H'00000226)	Operation
FC 03 / FC 16	MV Monitor (Heating)	2004	8196	MV Monitor (Heating)	-5.0 to 105.0 (Standard: HFFFFFFCE to H'0000041A)	Operation
FC 03 / FC 16	MV Monitor (Cooling)	2005	8197	MV Monitor (Cooling)	0.0 to 105.0 (Heating/Cooling: H'00000000 to H'0000041A)	Operation
FC 03 / FC 16	Set Point	2103	8451	Set Point	SP lower limit to SP upper limit	Operation
FC 03 / FC 16	Alarm Value 1	2104	8452	Alarm Value 1	-1999 to 9999 (HFFFFFF831 to H'0000270F)	Operation
FC 03 / FC 16	Alarm Value Upper Limit 1	2105	8453	Alarm Value Upper Limit 1	-1999 to 9999 (HFFFFFF831 to H'0000270F)	Operation
FC 03 / FC 16	Alarm Value Lower Limit 1	2106	8454	Alarm Value Lower Limit 1	-1999 to 9999 (HFFFFFF831 to H'0000270F)	Operation
FC 03 / FC 16	Alarm Value 2	2107	8455	Alarm Value 2	-1999 to 9999 (HFFFFFF831 to H'0000270F)	Operation
FC 03 / FC 16	Alarm Value Upper Limit 2	2108	8456	Alarm Value Upper Limit 2	-1999 to 9999 (HFFFFFF831 to H'0000270F)	Operation
FC 03 / FC 16	Alarm Value Lower Limit 2	2109	8457	Alarm Value Lower Limit 2	-1999 to 9999 (HFFFFFF831 to H'0000270F)	Operation
FC 03 / FC 16	Process Value (PV)	2402	9218	PV	Temperature/Analog specific range (See manual)	Operation
FC 03 / FC 16	Internal Set Point	2403	9219	Internal Set Point *1	SP lower limit to SP upper limit	Operation
FC 03 / FC 16	Multi-SP No. Monitor	2404	9220	Multi-SP No. Monitor	0 to 7 (H'00000000 to H'00000007)	Operation
FC 03 / FC 16	Status	2406	9222	Status 12	Refer to 5-2 Status for details	Operation
FC 03 / FC 16	Status	2407	9223	Status *3	Refer to 5-2 Status for details	Operation
FC 03 / FC 16	Status 2	2408	9224	Status 2 12	Refer to 5-2 Status for details	Operation
FC 03 / FC 16	Status 2	2409	9225	Status 2 13	Refer to 5-2 Status for details	Operation
FC 03 / FC 16	Decimal Point Monitor	2410	9232	Decimal Point Monitor	0 to 3 (H'00000000 to H'00000003)	Operation

Variable Area (Setting Range) List (Page 5-3)

type	description	address in Hex	address in decimal	parameter name	settings / range	level	default
holding register	Operation/Adjustment Protect	H'0500	2500	Operation/Adjustment Protect	H'00000000 (0): No restrictions in operation and adjustment levels H'00000001 (1): Move to adjustment level is prohibited. H'00000002 (2): Display and change of only "PV" and "PV/SP" parameters is allowed. H'00000003 (3): Display of only "PV" and "PV/SP" parameters is allowed.	Protect	H'00000000
holding register	Initial Setting/Communications Protect	H'0502	2501	Initial Setting/Comm Protect	H'00000000 (0): Move to initial setting/communications setting level is allowed. (Move to advanced function setting level is displayed.) H'00000001 (1): Move to initial setting/communications setting level is allowed. (Move to advanced function setting level is not displayed.) H'00000002 (2): Move to initial setting/communications setting level is prohibited.		H'00000000
holding register	Setting Change Protect	H'0504	2502	Setting Change Protect	H'00000000 (0): OFF (Changing of setup on controller display is allowed.) H'00000001 (1): ON (Changing of setup on controller display is prohibited.)		H'00000000
holding register	PF Key Protect	H'0506	2503	PF Key Protect	H'00000000 (0): OFF H'00000001 (1): ON		H'00000000
holding register	Move to Protect Level	H'0508	2504	Move to Protect Level	H'FFFFF831 to H'0000270F (-1999 to 9999)
holding register	Password to Move to Protect Level	H'050A	2505	Password to Move Protect Lvl	H'FFFFF831 to H'0000270F (-1999 to 9999) (Can only be set. The monitor value is always H'00000000.)		H'00000000
holding register	Parameter Mask Enable	H'050C	2506	Parameter Mask Enable	H'00000000 (0): OFF H'00000001 (1): ON		H'00000000
holding register	Changed Parameters Only	H'050E	2507	Changed Parameters Only	H'00000000 (0): OFF H'00000001 (1): ON		H'00000000
holding register	Manual MV	H'0600	2600	Manual MV	Standard Models: Standard control: H'FFFFFCE to H'0000041A (-5.0 to 105.0) Heating and cooling control: H'FFFFFBE6 to H'0000041A (-105.0 to 105.0) Position-proportional Models: Close position-proportional control with the Direct Setting of Position Proportional MV parameter set to ON: H'FFFFFCE to H'0000041A (-5.0 to 105.0)	Manual control
holding register	Set Point	H'0602	2601	Set Point	SP lower limit to SP upper limit	Operation
holding register	Remote SP Monitor	H'0604	2602	Remote SP Monitor	Remote SP lower limit -10% FS to Remote SP upper limit +10% FS
holding register	Heater Current 1 Value Monitor	H'0608	2604	Heater Current 1 Value Mon	H'00000000 to H'00000226 (0.0 to 55.0)
holding register	MV Monitor (Heating)	H'060A	2605	MV Monitor (Heating)	Standard control: H'FFFFFCE to H'0000041A (-5.0 to 105.0) Heating and cooling control: H'00000000 to H'0000041A (0.0 to 105.0)
holding register	MV Monitor (Cooling)	H'060C	2606	MV Monitor (Cooling)	H'00000000 to H'0000041A (0.0 to 105.0)
holding register	Valve Opening Monitor	H'060E	2607	Valve Opening Monitor	H'FFFFF9C to H'0000044C (-10.0 to 110.0)

Communications Data for Modbus (Page 5-4)

type	description	address in Hex	address in decimal	parameter name	settings / range	level	default
Read/Write Holding Register	Proportional Band (Cooling)	0701	1793	Proportional Band (Cooling)	H'00000001 to H'0000270F (0.1 to 999.9)	Adjustment
Read/Write Holding Register	Integral Time (Cooling)	0702	1794	Integral Time (Cooling)	H'00000000 to H'0000270F (0 to 9999: Integral/derivative time unit is 1 s.) (0.0 to 999.9: Integral/derivative time unit is 0.1 s.)	Adjustment
Read/Write Holding Register	Derivative Time (Cooling)	0703	1795	Derivative Time (Cooling)	H'00000000 to H'0000270F (0 to 9999: Integral/derivative time unit is 1 s.) (0.0 to 999.9: Integral/derivative time unit is 0.1 s.)	Adjustment
Read/Write Holding Register	Dead Band	0704	1796	Dead Band	H'FFFFF831 to H'0000270F (-199.9 to 999.9 for temperature input) (-19.99 to 99.99 for analog input)	Adjustment
Read/Write Holding Register	Manual Reset Value	0705	1797	Manual Reset Value	H'00000000 to H'000003E8 (0.0 to 100.0)	Adjustment
Read/Write Holding Register	Hysteresis (Heating)	0706	1798	Hysteresis (Heating)	H'00000001 to H'0000270F (0.1 to 999.9 for temperature input) (0.01 to 99.99 for analog input)	Adjustment
Read/Write Holding Register	Hysteresis (Cooling)	0707	1799	Hysteresis (Cooling)	H'00000001 to H'0000270F (0.1 to 999.9 for temperature input) (0.01 to 99.99 for analog input)	Adjustment
Read/Write Holding Register	Control Period (Heating)	0708	1800	Control Period (Heating)	H'FFFFFFFE (-2): 0.1 s H'FFFFFFFF (-1): 0.2 s H'00000000 (0): 0.5 s H'00000001 to H'00000063 (1 to 99)	Initial setting
Read/Write Holding Register	Control Period (Cooling)	0709	1801	Control Period (Cooling)	H'FFFFFFFE (-2): 0.1 s H'FFFFFFFF (-1): 0.2 s H'00000000 (0): 0.5 s H'00000001 to H'00000063 (1 to 99)	Initial setting
Read/Write Holding Register	Position Proportional Dead Band	070A	1802	Position Proportional Dead Band	H'00000001 to H'00000064 (0.1 to 10.0)	Adjustment
Read/Write Holding Register	Open/Close Hysteresis	070B	1803	Open/Close Hysteresis	H'00000001 to H'000000C8 (0.1 to 20.0)	Adjustment
Read/Write Holding Register	SP Ramp Time Unit	070C	1804	SP Ramp Time Unit	H'00000000 (0): EU/second H'00000001 (1): EU/minute H'00000002 (2): EU/hour	Advanced function setting
Read/Write Holding Register	SP Ramp Set Value	070D	1805	SP Ramp Set Value	H'00000000 (0): OFF H'00000001 to H'0000270F (1 to 9999)	Adjustment
Read/Write Holding Register	SP Ramp Fall Value	070E	1806	SP Ramp Fall Value	H'FFFFFFFF (-1): Same (Same as SP Ramp Set Value.) H'00000000 (0): OFF H'00000001 to H'0000270F (1 to 9999)	Adjustment
Read/Write Holding Register	MV at Stop	070F	1807	MV at Stop	Standard Models: Standard control: H'FFFFFCE to H'0000041A (-5.0 to 105.0) Heating and cooling control: H'FFFFFBE6 to H'0000041A (-105.0 to 105.0) Position-proportional Models: Close position-proportional control with the Direct Setting of Position Proportional MV parameter set to ON: H'FFFFFCE to H'0000041A (-5.0 to 105.0) Floating position-proportional control or the Direct Setting of Position Proportional MV parameter set to OFF: H'FFFFFFFF to H'00000001 (-1 to 1)	Adjustment
Read/Write Holding Register	MV at PV Error	0711	1809	MV at PV Error	Same as MV at Stop parameter	Adjustment
Read/Write Holding Register	MV Change Rate Limit	0713	1811	MV Change Rate Limit	H'00000000 to H'000003E8 (0.0 to 100.0)	Operation
Read/Write Holding Register	PV Input Slope Coefficient	0718	1816	PV Input Slope Coefficient	H'00000001 to H'0000270F (0.001 to 9.999)	Operation
Read/Write Holding Register	Heater Current 1 Value Monitor	071A	1818	Heater Current 1 Value Monitor	H'00000000 to H'00000226 (0.0 to 55.0)	Operation
Read/Write Holding Register	Heater Burnout Detection 1	071B	1819	Heater Burnout Detection 1	H'00000000 to H'000001F4 (0.0 to 50.0)	Adjustment
Read/Write Holding Register	Leakage Current 1 Monitor	071C	1820	Leakage Current 1 Monitor	H'00000000 to H'00000226 (0.0 to 55.0)	Operation
Read/Write Holding Register	HS Alarm 1	071D	1821	HS Alarm 1	H'00000000 to H'000001F4 (0.0 to 50.0)	Adjustment
Read/Write Holding Register	Process Value Input Shift	0723	1827	Process Value Input Shift	H'FFFFF831 to H'0000270F (-1999 to 9999)	Adjustment
Read/Write Holding Register	Heater Current 2 Value Monitor	0724	1828	Heater Current 2 Value Monitor	H'00000000 to H'00000226 (0.0 to 55.0)	Operation

Variable Area (Setting Range) List (Page 5-5)

type	description	address in Hex	address in decimal	parameter name	settings / range	level	default
Write Holding Register (FC 06/16)	Heater Burnout Detection 2	2725	10021	Heater Burnout Detection 2	H'00000000 to H'000001F4 (0.0 to 50.0)	Adjustment
Write Holding Register (FC 06/16)	Leakage Current 2 Monitor	2726	10022	Leakage Current 2 Monitor	H'00000000 to H'00000226 (0.0 to 55.0)	Operation
Write Holding Register (FC 06/16)	HS Alarm 2	2727	10023	HS Alarm 2	H'00000000 to H'000001F4 (0.0 to 50.0)	Adjustment
Write Holding Register (FC 06/16)	Soak Time Remain	2728	10024	Soak Time Remain	H'00000000 to H'0000270F (0 to 9999)	Operation
Write Holding Register (FC 06/16)	Soak Time	2729	10025	Soak Time	H'00000001 to H'0000270F (1 to 9999)	Adjustment
Write Holding Register (FC 06/16)	Wait Band	272A	10026	Wait Band	H'00000000 (0): OFF, H'00000001 to H'0000270F (0.1 to 999.9 for Temp input / 0.01 to 99.99 for Analog input)	Adjustment	OFF
Write Holding Register (FC 06/16)	Remote SP Input Shift	272B	10027	Remote SP Input Shift	H'FFFFF831 to H'0000270F (-1999 to 9999)	Advanced function setting
Write Holding Register (FC 06/16)	Remote SP Input Slope Coefficient	272C	10028	Remote SP Input Slope Coefficient	H'00000001 to H'0000270F (0.001 to 9.999)	Advanced function setting
Write Holding Register (FC 06/16)	Input Digital Filter	2800	10240	Input Digital Filter	H'00000000 to H'0000270F (0.0 to 999.9)	Advanced function setting
Write Holding Register (FC 06/16)	Moving Average Count	2804	10244	Moving Average Count	H'00000000 (0): OFF, H'00000001 (1): 2 times, H'00000002 (2): 4 times, H'00000003 (3): 8 times, H'00000004 (4): 16 times, H'00000005 (5): 32 times	Advanced function setting	OFF

Communications Data for Modbus (Page 5-6)

type	description	address in Hex	address in decimal	parameter name	settings / range	level
Holding Register	Extraction of Square Root Low-cut Point	2808	10248	Extraction of Square Root Low-cut Point	H'00000000 to H'000003E8 (0.0 to 100.0)	Adjustment
Holding Register	SP 0	2900	10496	SP 0	SP lower limit to SP upper limit	Operation
Holding Register	Alarm Value 1	2902	10498	Alarm Value 1	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	Alarm Value Upper Limit 1	2903	10499	Alarm Value Upper Limit 1	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	Alarm Value Lower Limit 1	2904	10500	Alarm Value Lower Limit 1	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	Alarm Value 2	2905	10501	Alarm Value 2	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	Alarm Value Upper Limit 2	2906	10502	Alarm Value Upper Limit 2	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	Alarm Value Lower Limit 2	2907	10503	Alarm Value Lower Limit 2	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	Alarm Value 3	2908	10504	Alarm Value 3	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	Alarm Value Upper Limit 3	2909	10505	Alarm Value Upper Limit 3	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	Alarm Value Lower Limit 3	290A	10506	Alarm Value Lower Limit 3	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	Alarm Value 4	290B	10507	Alarm Value 4	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	Alarm Value Upper Limit 4	290C	10508	Alarm Value Upper Limit 4	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	Alarm Value Lower Limit 4	290D	10509	Alarm Value Lower Limit 4	H'FFFFF831 to H'0000270F (-1999 to 9999)	Operation
Holding Register	SP 1	290E	10510	SP 1	SP lower limit to SP upper limit	Adjustment
Holding Register	SP 2	291C	10524	SP 2	SP lower limit to SP upper limit	Adjustment
Holding Register	SP 3	292A	10538	SP 3	SP lower limit to SP upper limit	Adjustment
Holding Register	SP 4	2938	10552	SP 4	SP lower limit to SP upper limit	Adjustment
Holding Register	SP 5	2946	10566	SP 5	SP lower limit to SP upper limit	Adjustment
Holding Register	SP 6	2954	10580	SP 6	SP lower limit to SP upper limit	Adjustment
Holding Register	SP 7	2962	10594	SP 7	SP lower limit to SP upper limit	Adjustment
Holding Register	Proportional Band	2A00	10752	Proportional Band	H'00000001 to H'0000270F (0.1 to 999.9)	Adjustment
Holding Register	Integral Time	2A01	10753	Integral Time	Standard, heating/cooling, or close position proportional control: H'00000000 to H'0000270F (0 to 9999: Integral/derivative time unit is 1 s.) (0.0 to 999.9: Integral/derivative time unit is 0.1 s.) Floating position-proportional control: H'00000001 to H'0000270F (1 to 9999: Integral/derivative time unit is 1 s.) (0.1 to 999.9: Integral/derivative time unit is 0.1 s.)	Adjustment
Holding Register	Derivative Time	2A02	10754	Derivative Time	H'00000000 to H'0000270F (0 to 9999: Integral/derivative time unit is 1 s.) (0.0 to 999.9: Integral/derivative time unit is 0.1 s.)	Adjustment
Holding Register	MV Upper Limit	2A05	10757	MV Upper Limit	Standard control or close position-proportional control: MV lower limit + 0.1 to H'0000041A (MV lower limit + 0.1 to 105.0) Heating and cooling control: H'00000000 to H'0000041A (0.0 to 105.0)	Adjustment
Holding Register	MV Lower Limit	2A06	10758	MV Lower Limit	Standard control or close position-proportional control: H'FFFFFFCE to MV upper limit -0.1 (-5.0 to MV upper limit -0.1) Heating and cooling control: H'FFFFFBE6 to H'00000000 (-105.0 to 0.0)	Adjustment

Modbus Registers (Page 5-7)

type	description	address in Hex	address in decimal	parameter name	settings / range	level	default
03/06/16	Input Type	2C00	11264	Input Type	H'00000000 (0): Pt (-200 to 850°C/-300 to 1500°F) H'00000001 (1): Pt (-199.9 to 500.0°C/-199.9 to 900.0°F) H'00000002 (2): Pt (0.0 to 100.0°C/0.0 to 210.0°F) H'00000003 (3): JPt (-199.9 to 500.0°C/-199.9 to 900.0°F) H'00000004 (4): JPt (0.0 to 100.0°C/0.0 to 210.0°F) H'00000005 (5): K (-200 to 1300°C/-300 to 2300°F) H'00000006 (6): K (-20.0 to 500.0°C/0.0 to 900.0°F) H'00000007 (7): J (-100 to 850°C/-100 to 1500°F) H'00000008 (8): J (-20.0 to 400.0°C/0.0 to 750.0°F) H'00000009 (9): T (-200 to 400°C/-300 to 700°F) H'0000000A (10): T (-199.9 to 400.0°C/-199.9 to 700.0°F) H'0000000B (11): E (-200 to 600°C/-300 to 1100°F) H'0000000C (12): L (-100 to 850°C/-100 to 1500°F) H'0000000D (13): U (-200 to 400°C/-300 to 700°F) H'0000000E (14): U (-199.9 to 400.0°C/-199.9 to 700.0°F) H'0000000F (15): N (-200 to 1300°C/-300 to 2300°F) H'00000010 (16): R (0 to 1700°C/0 to 3000°F) H'00000011 (17): S (0 to 1700°C/0 to 3000°F) H'00000012 (18): B (100 to 1800°C/300 to 3200°F) H'00000013 (19): W (0 to 2,300°C/0 to 3,200°F) H'00000014 (20): PLII (0 to 1,300°C/0 to 2,300°F) H'00000015 (21): Infrared temperature sensor (K 140°F/60°C) H'00000016 (22): Infrared temperature sensor (K 240°F/120°C) H'00000017 (23): Infrared temperature sensor (K 280°F/140°C) H'00000018 (24): Infrared temperature sensor (K 440°F/220°C) H'00000019 (25): 4 to 20 mA H'0000001A (26): 0 to 20 mA H'0000001B (27): 1 to 5 V H'0000001C (28): 0 to 5 V H'0000001D (29): 0 to 10 V H'0000001E (30): 0 to 50 mV	Initial setting
03/06/16	Temperature Unit	2C01	11265	Temperature Unit	H'00000000 (0): °C H'00000001 (1): °F
03/06/16	Scaling Lower Limit	2C09	11273	Scaling Lower Limit	H'FFFFF831 to scaling upper limit –1 (–1999 to scaling upper limit –1)
03/06/16	Scaling Upper Limit	2C0B	11275	Scaling Upper Limit	Scaling lower limit + 1 to H'0000270F (Scaling lower limit + 1 to 9999)
03/06/16	Decimal Point	2C0C	11276	Decimal Point	H'00000000 to 00000003 (0 to 3)
03/06/16	Remote SP Upper limit	2C0D	11277	Remote SP Upper limit	Input range lower limit to Input range upper limit for temperature input Scaling lower limit to Scaling upper limit for analog input	Advanced function setting
03/06/16	Remote SP Lower limit	2C0E	11278	Remote SP Lower limit	Input range lower limit to Input range upper limit for temperature input Scaling lower limit to Scaling upper limit for analog input	Advanced function setting
03/06/16	PV Decimal Point Display	2C0F	11279	PV Decimal Point Display	H'00000000 (0): OFF H'00000001 (1): ON
03/06/16	Control Output 1 Signal	2D03	11523	Control Output 1 Signal	H'00000000 (0): 4 to 20 mA H'00000001 (1): 0 to 20 mA	Initial setting
03/06/16	Control Output 2 Signal	2D04	11524	Control Output 2 Signal	H'00000000 (0): 4 to 20 mA H'00000001 (1): 0 to 20 mA
03/06/16	SP Upper Limit	2D0F	11535	SP Upper Limit	The range of values (without decimal point) is as follows: Temperature input: SP lower limit + 1 to Input range upper limit Analog input: SP lower limit + 1 to Scaling upper limit
03/06/16	SP Lower Limit	2D10	11536	SP Lower Limit	The range of values (without decimal point) is as follows: Temperature input: Input range lower limit to SP upper limit - 1 Analog input: Scaling lower limit to SP upper limit - 1
03/06/16	Standard or Heat/Cool	2D11	11537	Standard or Heating/Cooling	H'00000000 (0): Standard H'00000001 (1): Heating and cooling	Initial setting

Communications Data for Modbus (Page 5-8)

type	description	address in Hex	address in decimal	parameter name	settings / range	level
Holding Register (Read/Write)	Direct/Reverse Operation	2D12	11538	Direct/Reverse Operation	H'00000000 (0): Reverse operation H'00000001 (1): Direct operation	Initial setting
Holding Register (Read/Write)	Close/Floating	2D13	11539	Close/Floating	H'00000000 (0): Floating H'00000001 (1): Close
Holding Register (Read/Write)	PID ON/OFF	2D14	11540	PID ON/OFF	H'00000000 (0): ON/OFF H'00000001 (1): 2 PID control
Holding Register (Read/Write)	ST	2D15	11541	ST	H'00000000 (0): OFF H'00000001 (1): ON
Holding Register (Read/Write)	Program Pattern	2D16	11542	Program Pattern	H'00000000 (0): OFF H'00000001 (1): STOP H'00000002 (2): CONT
Holding Register (Read/Write)	Remote SP Input	2D18	11544	Remote SP Input	H'00000000 (0): 4 to 20 mA H'00000001 (1): 0 to 20 mA H'00000002 (2): 1 to 5 V H'00000003 (3): 0 to 5 V H'00000004 (4): 0 to 10 V	Advanced function setting
Holding Register (Read/Write)	Minimum Output ON/OFF Band	2D19	11545	Minimum Output ON/OFF Band	H'00000000 to H'000001F4 (0.0 to 50.0)
Holding Register (Read/Write)	Transfer Output Type	2E00	11776	Transfer Output Type	H'00000000 (0): OFF H'00000001 (1): Set point H'00000002 (2): Set point during SP ramp H'00000003 (3): PV H'00000004 (4): MV (heating) H'00000005 (5): MV (cooling) ...	Initial setting
Holding Register (Read/Write)	Transfer Output Signal	2E01	11777	Transfer Output Signal	H'00000000 (0): 4 to 20 mA H'00000001 (1): 1 to 5 V

Communications Data for Modbus (Page 5-9)

type	description	address in Hex	address in decimal	parameter name	settings / range	level	default
write holding register	Control Output 1 Assignment parameter	0x2E06	11782	Control Output 1 Assignment	Relay/Voltage Output: H'00000000 (0) to H'00000016 (22) (0: Not assigned, 1: Ctrl output (heating), 2: Ctrl output (cooling), 3: Alarm 1, 4: Alarm 2, 5: Alarm 3, 6: Alarm 4, 7: Heater alarm, 8: HB alarm, 9: HS alarm, 10: Input error, 11: RSP input error, 12: P.END output*1, 13: RUN output, 14: Integrated alarm, 15: Work bit 1, 16: Work bit 2, 17: Work bit 3, 18: Work bit 4, 19: Work bit 5, 20: Work bit 6, 21: Work bit 7, 22: Work bit 8) Linear Current Output: H'FFFFFFFB (-5) to H'FFFFFFFF (-1), H'00000000 (0) to H'00000002 (2)	Advanced function setting	-
write holding register	Control Output 2 Assignment parameter	0x2E07	11783	Control Output 2 Assignment	Relay/Voltage Output: H'00000000 (0) to H'00000016 (0 to 22) Linear Current Output: H'00000000 (0) to H'00000002 (0 to 2) (Note: Settings are same as Control Output 1, except for items marked with *2 for linear output)	Advanced function setting	-

Modbus Register Map (Page 5-10)

type	description	address in Hex	address in decimal	parameter name	settings / range	level	default
Write Holding Register (06/16)	Event Input Assignment 1	2E0A	11786	Event Input Assignment 1	H'00000000 to H'0000000D (0 to 13)	Initial setting	0 (None)
Write Holding Register (06/16)	Event Input Assignment 2	2E0B	11787	Event Input Assignment 2	H'00000000 to H'0000000D (0 to 13)
Write Holding Register (06/16)	Event Input Assignment 3	2E0C	11788	Event Input Assignment 3	H'00000000 to H'0000000D (0 to 13)
Write Holding Register (06/16)	Event Input Assignment 4	2E0D	11789	Event Input Assignment 4	H'00000000 to H'0000000D (0 to 13)
Write Holding Register (06/16)	Event Input Assignment 5	2E0E	11790	Event Input Assignment 5	H'00000000 to H'0000000D (0 to 13)
Write Holding Register (06/16)	Event Input Assignment 6	2E0F	11791	Event Input Assignment 6	H'00000000 to H'0000000D (0 to 13)
Write Holding Register (06/16)	Auxiliary Output 1 Assignment	2E10	11792	Auxiliary Output 1 Assignment	H'00000000 to H'00000016 (0 to 22)	Advanced function setting	0 (None)
Write Holding Register (06/16)	Auxiliary Output 2 Assignment	2E11	11793	Auxiliary Output 2 Assignment	H'00000000 to H'00000016 (0 to 22)
Write Holding Register (06/16)	Auxiliary Output 3 Assignment	2E12	11794	Auxiliary Output 3 Assignment	H'00000000 to H'00000016 (0 to 22)
Write Holding Register (06/16)	Auxiliary Output 4 Assignment	2E13	11795	Auxiliary Output 4 Assignment	H'00000000 to H'00000016 (0 to 22)
Write Holding Register (06/16)	Transfer Output Upper Limit	2E14	11796	Transfer Output Upper Limit	H'FFFFF831 to H'0000270F (-1999 to 9999) *2	Initial setting
Write Holding Register (06/16)	Transfer Output Lower Limit	2E15	11797	Transfer Output Lower Limit	H'FFFFF831 to H'0000270F (-1999 to 9999) *2	Initial setting

Variable Area (Setting Range) List 5-11

type	description	address in Hex	address in decimal	parameter name	settings / range	level	default
read/write holding register	Simple Transfer Output 1 Upper Limit	2E16	11798	Simple Transfer Output 1 Upper Limit	HFFFFF831 to H0000270F (-1999 to 9999)	Initial setting
read/write holding register	Simple Transfer Output 1 Lower Limit	2E17	11799	Simple Transfer Output 1 Lower Limit	HFFFFF831 to H0000270F (-1999 to 9999)	Initial setting

Communications Data (Page 5-12)

type	description	address in Hex	address in decimal	parameter name	settings / range	level
Holding Register (03/06/16)	Extraction of Square Root Enable	2E24	11812	Extraction of Square Root Enable	0: OFF 1: ON	Initial setting
Holding Register (03/06/16)	Travel Time	2E30	11824	Travel Time	1 to 999
Holding Register (03/06/16)	Alarm 1 Type	2F00	12032	Alarm 1 Type	0: Alarm function OFF 1: Upper and lower-limit alarm 2: Upper-limit alarm 3: Lower-limit alarm 4: Upper and lower-limit range alarm 5: Upper and lower-limit alarm with standby sequence 6: Upper-limit alarm with standby sequence 7: Lower-limit alarm with standby sequence 8: Absolute-value upper-limit alarm 9: Absolute-value lower-limit alarm 10: Absolute-value upper-limit alarm with standby sequence 11: Absolute-value lower-limit alarm with standby sequence 12: LBA (Loop Burnout Alarm) 13: PV change rate alarm 14: SP absolute-value upper-limit alarm 15: SP absolute-value lower-limit alarm 16: MV absolute-value upper-limit alarm 17: MV absolute-value lower-limit alarm 18: RSP absolute-value upper-limit alarm * 19: RSP absolute-value lower-limit alarm Valid only with a remote SP input.
Holding Register (03/06/16)	Alarm 1 Latch	2F01	12033	Alarm 1 Latch	0: OFF 1: ON	Advanced function setting
Holding Register (03/06/16)	Alarm 1 Hysteresis	2F02	12034	Alarm 1 Hysteresis	1 to 9999 (0.1 to 999.9 for temperature input) (0.01 to 99.99 for analog input)	Initial setting
Holding Register (03/06/16)	Alarm 2 Type	2F03	12035	Alarm 2 Type	0 to 19 Note: Same settings as the Alarm 1 Type. However, the LBA (loop burnout alarm) cannot be set.
Holding Register (03/06/16)	Alarm 2 Latch	2F04	12036	Alarm 2 Latch	0: OFF 1: ON	Advanced function setting
Holding Register (03/06/16)	Alarm 2 Hysteresis	2F05	12037	Alarm 2 Hysteresis	1 to 9999 (0.1 to 999.9 for temperature input) (0.01 to 99.99 for analog input)	Initial setting
Holding Register (03/06/16)	Alarm 3 Type	2F06	12038	Alarm 3 Type	0 to 19 Note: Same settings as the Alarm 1 Type. However, the LBA (loop burnout alarm) cannot be set.
Holding Register (03/06/16)	Alarm 3 Latch	2F07	12039	Alarm 3 Latch	0: OFF 1: ON	Advanced function setting
Holding Register (03/06/16)	Alarm 3 Hysteresis	2F08	12040	Alarm 3 Hysteresis	1 to 9999 (0.1 to 999.9 for temperature input) (0.01 to 99.99 for analog input)	Initial setting
Holding Register (03/06/16)	Alarm 4 Type	2F09	12041	Alarm 4 Type	0 to 19 Note: Same settings as the Alarm 1 Type. However, the LBA (loop burnout alarm) cannot be set.
Holding Register (03/06/16)	Alarm 4 Latch	2F0A	12042	Alarm 4 Latch	0: OFF 1: ON	Advanced function setting
Holding Register (03/06/16)	Alarm 4 Hysteresis	2F0B	12043	Alarm 4 Hysteresis	1 to 9999 (0.1 to 999.9 for temperature input) (0.01 to 99.99 for analog input)	Initial setting
Holding Register (03/06/16)	Standby Sequence Reset	2F0C	12044	Standby Sequence Reset	0: Condition A 1: Condition B	Advanced function setting
Holding Register (03/06/16)	Auxiliary Output 1 Open in Alarm	2F0D	12045	Auxiliary Output 1 Open in Alarm	0: Close in alarm 1: Open in alarm	Advanced function setting

Variable Area (Setting Range) List (Page 5-13)

type	description	address in Hex	address in decimal	parameter name	settings / range	level
write holding register	Auxiliary Output 2 Open in Alarm	2F0E	12046	Auxiliary Output 2 Open in Alarm	H'00000000 (0): Close in alarm H'00000001 (1): Open in alarm	Advanced function setting
write holding register	Auxiliary Output 3 Open in Alarm	2F0F	12047	Auxiliary Output 3 Open in Alarm	H'00000000 (0): Close in alarm H'00000001 (1): Open in alarm	Advanced function setting
write holding register	Auxiliary Output 4 Open in Alarm	2F10	12048	Auxiliary Output 4 Open in Alarm	H'00000000 (0): Close in alarm H'00000001 (1): Open in alarm	Advanced function setting
write holding register	Alarm 1 ON delay	2F11	12049	Alarm 1 ON delay	H'00000000 to H'000003E7 (0 to 999)
write holding register	Alarm 2 ON delay	2F12	12050	Alarm 2 ON delay	H'00000000 to H'000003E7 (0 to 999)
write holding register	Alarm 3 ON delay	2F13	12051	Alarm 3 ON delay	H'00000000 to H'000003E7 (0 to 999)
write holding register	Alarm 4 ON delay	2F14	12052	Alarm 4 ON delay	H'00000000 to H'000003E7 (0 to 999)
write holding register	Alarm 1 OFF delay	2F15	12053	Alarm 1 OFF delay	H'00000000 to H'000003E7 (0 to 999)
write holding register	Alarm 2 OFF delay	2F16	12054	Alarm 2 OFF delay	H'00000000 to H'000003E7 (0 to 999)
write holding register	Alarm 3 OFF delay	2F17	12055	Alarm 3 OFF delay	H'00000000 to H'000003E7 (0 to 999)
write holding register	Alarm 4 OFF delay	2F18	12056	Alarm 4 OFF delay	H'00000000 to H'000003E7 (0 to 999)
write holding register	PV/SP No. 1 Display Selection	3000	12288	PV/SP No. 1 Display Selection	H'00000000 (0):Nothing displayed. H'00000001 (1):PV/SP H'00000002 (2):PV H'00000003 (3):PV/SP (character display) H'00000004 (4):PV/SP/MV H'00000005 (5):PV/SP/Multi-SP No. H'00000006 (6):PV/SP/Soak time remain H'00000007 (7):PV/SP/Ramp SP H'00000008 (8):PV/SP/Alarm value 1
write holding register	MV Display Selection	3001	12289	MV Display Selection	H'00000000 (0): MV (heating) H'00000001 (1): MV (cooling)
write holding register	Automatic Display Return Time	3003	12291	Automatic Display Return Time	H'00000000 (0): OFF H'00000001 to H'00000063 (1 to 99)
write holding register	Display Refresh Period	3004	12292	Display Refresh Period	H'00000000 (0):OFF H'00000001 (1): 0.25 H'00000002 (2): 0.5 H'00000003 (3): 1.0
write holding register	PV/SP No. 2 Display Selection	3008	12296	PV/SP No. 2 Display Selection	H'00000000 to H'00000008 (0 to 8) Note: Same as PV/SP No. 1 Display Selection.
write holding register	Display Brightness	300A	12298	Display Brightness	H'00000001 to H'00000003 (1 to 3)
write holding register	MV Display	300B	12299	MV Display	H'00000000 (0): OFF H'00000001 (1): ON
write holding register	Move to Protect Level Time	300C	12300	Move to Protect Level Time	H'00000001 to H'0000001E (1 to 30)
write holding register	Auto/Manual Select Addition	300F	12303	Auto/Manual Select Addition	H'00000000 (0): OFF H'00000001 (1): ON
write holding register	PV Status Display Function	3011	12305	PV Status Display Function	H'00000000 (0): OFF H'00000001 (1): Manual H'00000002 (2): Stop H'00000003 (3): Alarm 1 H'00000004 (4): Alarm 2 H'00000005 (5): Alarm 3 H'00000006 (6): Alarm 4 H'00000007 (7): Alarm 1 to 4 OR status H'00000008 (8): Heater alarm H'00000009 (9): Status display message*1
write holding register	SV Status Display Function	3012	12306	SV Status Display Function	H'00000000 to H'00000009 (0 to 9) Note: Same as for PV Status Display Function.

Communications Data (Page 5-14)

type	description	address in Hex	address in decimal	parameter name	settings / range	level	default
03 (read) / 06/16 (write) Holding Register	Protocol Setting	0C1C	3100	Protocol Setting (See note.)	0: CompoWay/F, 1: Modbus	Communications setting
03 (read) / 06/16 (write) Holding Register	Communications Unit Number	0C1D	3101	Communications Unit No. *	0 to 99	Communications setting
03 (read) / 06/16 (write) Holding Register	Communications Baud Rate	0C1E	3102	Communications Baud Rate *	3: 9.6 kbps, 4: 19.2 kbps, 5: 38.4 kbps, 6: 57.6 kbps	Communications setting
03 (read) / 06/16 (write) Holding Register	Communications Data Length	0C1F	3103	Communications Data Length *	7: 7 bits, 8: 8 bits	Communications setting
03 (read) / 06/16 (write) Holding Register	Communications Stop Bits	0C20	3104	Communications Stop Bits *	1: 1 bit, 2: 2 bits	Communications setting
03 (read) / 06/16 (write) Holding Register	Communications Parity	0C21	3105	Communications Parity *	0: None, 1: Even, 2: Odd	Communications setting
03 (read) / 06/16 (write) Holding Register	Send Data Wait Time	0C22	3106	Send Data Wait Time *	0 to 99	Communications setting
03 (read) / 06/16 (write) Holding Register	PF Setting	0C80	3200	PF Setting	0: Disabled, 1: Run, 2: Stop, 3: RUN/STOP, 4: 100% AT exec/cancel, 5: 40% AT exec/cancel, 6: Alarm latch cancel, 7: Auto/man switch, 8: Mon/set item, 9: Digit shift key	Advanced function setting
03 (read) / 06/16 (write) Holding Register	Monitor/Setting Item 1 assignment	0C82	3202	Monitor/Setting Item 1	0 to 23 (Selects item to monitor/set, see list in manual: e.g., 0: Disabled, 1: PV/SP/multi-SP, ..., 23: Derivative Time (Cooling))	Advanced function setting
03 (read) / 06/16 (write) Holding Register	Monitor/Setting Item 2 assignment	0C83	3203	Monitor/Setting Item 2	0 to 23 (Same options as Item 1)	Advanced function setting
03 (read) / 06/16 (write) Holding Register	Monitor/Setting Item 3 assignment	0C84	3204	Monitor/Setting Item 3	0 to 23 (Same options as Item 1)	Advanced function setting
03 (read) / 06/16 (write) Holding Register	Monitor/Setting Item 4 assignment	0C85	3205	Monitor/Setting Item 4	0 to 23 (Same options as Item 1)	Advanced function setting
03 (read) / 06/16 (write) Holding Register	Monitor/Setting Item 5 assignment	0C86	3206	Monitor/Setting Item 5	0 to 23 (Same options as Item 1)	Advanced function setting

Variable Area (Setting Range) List - Page 5-15

type	description	address in Hex	address in decimal	parameter name	settings / range	level	default
Read/Write Holding Register	SP Tracking	3301	13057	SP Tracking	H'00000000 (0): OFF H'00000001 (1): ON	Advanced function setting	0 (OFF)
Read/Write Holding Register	PV Dead Band	3304	13060	PV Dead Band	H'00000000 to H'0000270F (0 to 9999)	Advanced function setting
Read/Write Holding Register	Cold Junction Compensation Method	3305	13061	Cold Junction Comp Method	H'00000000 (0): OFF H'00000001 (1): ON	Advanced function setting	0 (OFF)
Read/Write Holding Register	Integral/Derivative Time Unit	3309	13065	Integral/Derivative Unit	H'00000000 (0): 1 s H'00000001 (1): 0.1 s	Advanced function setting	0 (1 s)
Read/Write Holding Register	α	330A	13066	α	H'00000000 to H'00000064 (0.00 to 1.00)	Advanced function setting
Read/Write Holding Register	Manual Output Method	330C	13068	Manual Output Method	H'00000000 (0): HOLD H'00000001 (1): INIT	Advanced function setting	0 (HOLD)
Read/Write Holding Register	Manual MV Initial Value	330D	13069	Manual MV Initial Value	Standard control: HFFFFFFCE to H'0000041A (-5.0 to 105.0) Heating/cooling: HFFFFFBE6 to H'0000041A (-105.0 to 105.0)	Advanced function setting
Read/Write Holding Register	AT Calculated Gain	330F	13071	AT Calculated Gain	H'00000001 to H'00000064 (0.1 to 10.0)	Advanced function setting
Read/Write Holding Register	AT Hysteresis	3310	13072	AT Hysteresis	H'00000001 to H'0000270F (0.1 to 999.9 for temp input) H'00000001 to H'000003E7 (0.01 to 9.99 for analog input)	Advanced function setting
Read/Write Holding Register	Limit Cycle MV Amplitude	3311	13073	Limit Cycle MV Amplitude	H'00000032 to H'000001F4 (5.0 to 50.0)	Advanced function setting
Read/Write Holding Register	Heater Burnout Latch	3314	13076	Heater Burnout Latch	H'00000000 (0): OFF H'00000001 (1): ON	Advanced function setting	0 (OFF)
Read/Write Holding Register	Heater Burnout Hysteresis	3315	13077	Heater Burnout Hysteresis	H'00000001 to H'000001F4 (0.1 to 50.0)	Advanced function setting
Read/Write Holding Register	HS Alarm Latch	3316	13078	HS Alarm Latch	H'00000000 (0): OFF H'00000001 (1): ON	Advanced function setting	0 (OFF)
Read/Write Holding Register	HS Alarm Hysteresis	3317	13079	HS Alarm Hysteresis	H'00000001 to H'000001F4 (0.1 to 50.0)	Advanced function setting
Read/Write Holding Register	Number of Multi-SP Points	331B	13083	Number of Multi-SP Points	H'00000002 to H'00000008 (2 to 8)	Advanced function setting
Read/Write Holding Register	HB ON/OFF	331C	13084	HB ON/OFF	H'00000000 (0): OFF H'00000001 (1): ON	Advanced function setting	0 (OFF)
Read/Write Holding Register	Integrated Alarm Assignment	331E	13086	Integrated Alarm Assign	H'00000000 to H'000000FF (0 to 255)	Advanced function setting
Read/Write Holding Register	MV at Stop and Error Addition	3320	13088	MV at Stop/Error Add	H'00000000 (0): OFF H'00000001 (1): ON	Advanced function setting	0 (OFF)
Read/Write Holding Register	ST Stable Range	3321	13089	ST Stable Range	H'00000001 to H'0000270F (0.1 to 999.9)	Advanced function setting
Read/Write Holding Register	RT	3322	13090	RT	H'00000000 (0): OFF H'00000001 (1): ON (Valid only with temp input)	Advanced function setting	0 (OFF)
Read/Write Holding Register	HS Alarm Use	3323	13091	HS Alarm Use	H'00000000 (0): OFF H'00000001 (1): ON	Advanced function setting	0 (OFF)
Read/Write Holding Register	LBA Detection Time	3324	13092	LBA Detection Time	H'00000000 to H'0000270F (0 to 9999)	Advanced function setting
Read/Write Holding Register	LBA Level	3325	13093	LBA Level	H'00000001 to H'0000270F (0.1 to 999.9 for temp input) (0.01 to 99.99 for analog input)	Advanced function setting
Read/Write Holding Register	LBA Band	3326	13094	LBA Band	H'00000000 to H'0000270F (0.0 to 999.9 for temp input) (0.00 to 99.99 for analog input)	Advanced function setting
Read/Write Holding Register	Soak Time Unit	3327	13095	Soak Time Unit	H'00000000 (0): Minutes H'00000001 (1): Hours H'00000002 (2): Seconds*1	Advanced function setting	0 (Minutes)
Read/Write Holding Register	Alarm SP Selection	3328	13096	Alarm SP Selection	H'00000000 (0): Set point during SP ramp H'00000001 (1): Set point	Advanced function setting	0 (SP ramp)
Read/Write Holding Register	Remote SP Enable	3329	13097	Remote SP Enable	H'00000000 (0): OFF H'00000001 (1): ON	Advanced function setting	0 (OFF)
Read/Write Holding Register	Manual MV Limit Enable	332B	13099	Manual MV Limit Enable	H'00000000 (0): OFF H'00000001 (1): ON	Advanced function setting	0 (OFF)
Read/Write Holding Register	Direct Setting of Position Prop MV	332C	13100	Direct Setting Prop MV	H'00000000 (0): OFF H'00000001 (1): ON	Advanced function setting	0 (OFF)
Read/Write Holding Register	PV Rate of Change Calc Period	332D	13101	PV Rate Change Period	H'00000001 to H'000003E7 (1 to 999)	Advanced function setting

Communications Data for Modbus (Page 5-16)

type	description	address in Hex	address in decimal	parameter name	settings / range	level	default
Holding Register (03/06/16)	Heating/Cooling Tuning Method	332E	13102	Heating/Cooling Tuning Method	H'00000000 (0): Same as heating control. H'00000001 (1): Linear H'00000002 (2): Air cooling H'00000003 (3): Water cooling	Advanced function setting	-
Holding Register (03/06/16)	LCT Cooling Output Minimum ON Time (Not supported on version 2.0 or earlier of the E5CC, E5EC, or E5AC.)	3335	13109	LCT Cooling Output Minimum ON Time	H'00000001 to H'0000000A (0.1 to 1.0)	-	-